Sinotruk 8X4 Concrete Mixer Truck
Product Features
1. The tank body uses double helical blades that makes its density moderate, with symmetrical mixing board on the front taper place; double blades and guiding blades of discharge are installed on the outlet of tank, which makes the discharge more evenly, faster in speed, and convenient for the pumping transportation of other devices (such as automobile pump).
2. Low angle for mixing drum can extend the service life of hydraulic pump, motor and reducer. The sub frame uses high intensity square tube with damping in the central area that can play role when vehicle is at full load and under the bad conditions of road, which can lower the center of gravity of truck and make it move more smoothly.
3. The upload production of this mixer adopts multiple advanced technology, which can produce various types of mixer in volume such as 3m3, 5m3,6m3,8m3, 9m3,10m3, 12 m3 etc.
| Truck Model | ZZ1317N3667A |
| ENGINE | Make: SINOTRUKDiesel 4-stroke direct injection diesel engineEngine model: WD615.47, Euro II, 371HP With Oil Bath Filter System 6-cylinder in-line with water cooling, turbo-charging and intercooling Displacement: 9.726 L Optional: WD615.62 / WD615.87 / WD615.69 / WD615.47 |
| Cabin | HW76 cab, with one sleeper and two seats, 2-arm windscreen wiper system with three speeds, damped adjustable driver’s seat, with heating and ventilating system, exterior sun visor, safety belts, adjustable steering wheel, air horn, air conditioner, with transverse stabilizer,with 4-point support fully floating suspension + shock absorber.High steel bumper, With inter-cooler fenceOption: air suspension driver’s seat, high roof double bunk, fire extinguisher, warning light |
| Clutch | Single-plate dry coil-spring clutch, hydraulically operating with air assistance |
| Transmission | HW15710 / HW19710, 10F & 2RRatio: 14.28, 10.62, 7.87, 5.88, 4.38, 3.27, 2.43, 1.80, 1.34, 1.00, 13.91(R1), 3.18(R2) |
| Propeller Shaft | Double universal joint propeller shaft with gear-shaped coupling flange |
| Front Axle | HF9, 2 X 9000 KGSSteering with double T-cross section beamOptional:HF7, 2 x 7000kgs, drum type |
| Rear Axle | HC16,2 x 16000 KGSPressed axle housing, central single reduction with hub reduction and with differential locks between wheels and axles.Ratio::4.8 / 5.73 Optional:ST16,double reduction, speed ratio:3.93,4.42,4.8/ MCY13, 2 x 13000kgs |
| Chassis | Frame: U-profile parallel ladder frame with section of 300x80x8mm, and reinforced subframe all cold riveted cross membersFront suspension:10 semi-elliptic leaf spring, hydraulic telescopic double-action shock absorbers and stabilizerRear suspension:12 leaf semi-elliptic springs, bogie spring and stabilizer |
| Steering | ZF power steering, model ZF8118, hydraulic steering with power assistance |
| Overall Dimension | 10820 * 2550 * 3900mm |
| Mixer tank effective volume | Size:16cbmWith Italian brand Bonfiglioli reduction gears, America brand Eton oil pump and motor |
| Brake | Service brake: dual circuit compressed air brakeParking brake (emergency brake): spring energy, compressed air operating on front shaft and rear wheelsAuxiliary brake: engine exhaust brake Optional:EVB, ABS, AUTOMATICSLACK ADJUSTER |
| Tyres | 12.00R20,Radial (steel wire) Tires,1 spare tyreOption: 12.00-20, 12R22.5, 315/80R22.5, 12.00R24 |
| Electrics | Operating voltage: 24 V, negative grounded Starter: 24 V, 5.4 KwAlternator: 3-phase, 28 V, 1500 W Batteries: 2 x 12 V, 165 AhCigar-lighter, horn, headlamps, fog lights, brake lights, indicators and reverse light |
| Instrument Panel | Active check central control with indicators, with this integral instrument the daily manual checks on the vehicle and combined indicators of compressed air pressure, coolant temperature, engine oil pressure and battery charging. |
| Color | Optional |
On-demand customization, please leave a message for consultation